Showing posts with label 4-bit. Show all posts
Showing posts with label 4-bit. Show all posts

Tuesday, 4 June 2013

First Observations of Ionospheric Scintillation in 4-bit mode

On Monday, we reported about experimenting with the 4-bit mode now available at the station.  This allows us to cover up to 190.6 Mhz of continuous bandwidth, four times the amount available using the usual 16-bit mode.  Of course, the low-band and high-band filters only allow up to 80 MHz of continuous bandwidth in any of the 100 MHz Nyquist zones, but it does mean that we can use mode 357 to cover fully the frequency ranges 10-90 MHz, 110-190 MHz and 210-244 MHz simultaneously.  Also, as reported on Monday, there is an issue with saturation across the peak of sensitivity in the low band.

On Sunday night, we carried out the first ionospheric scintillation (as detailed here) observation of Cas A using 4-bit mode.  To alleviate the saturation issue as much as possible, we used the maximum 8 dB attenuation on the signal.  The results look pretty good:

Looking carefully, you can still see a faint band around the 50-60 MHz range, but the scintillation is still clearly visible across this band.  The data themselves also show some very interesting features in the low band, as shown in the 'zoomed-in' image below:

The image is displayed in grey-scale to bring out the features more.  There is a lot of detail to be analysed in these data, particularly as there is no spacing between subbands in 4-bit mode, making it clear that the 4-bit mode is well-enough suited for these kinds of observations.

Monday, 3 June 2013

Observing with 190.6 MHz bandwidth

Almost as soon as KAIRA was switched on, we worked out a way to observing with both the High-Band Antenna (HBA) and Low-Band Antenna (LBA) arrays. This is the so-called Mode-357 Observing. This method of observing has been extremely useful, not just to our own observers, but also for other members of the LOFAR community (of course, our scripts can be easily adapted to work on other LOFAR stations). However, the (initial) limitation of this form of observing is that your are still limited to a maximum of 244 beamlets. Each beamlet is a pointing direction and a frequency channel (~195 kHz wide), which means the total bandwidth you that can be observed is about 47.6 MHz. Still, we have been using that successfully for various projects (such as ionospheric scintillation).

In April, we upgraded the KAIRA station with the new LOFAR software. This included some new signal processing modes, specifically: 8-bit and 4-bit mode.

By default, the LOFAR samplers in the signal processing hardware operate at 12-bit. However, by reducing the number of bits, it is possible to increase the number of beamlets. LOFAR 8-bit mode can have 488 beamlets, and LOFAR 4-bit mode can have 976 beamlets. This additional number allows either extra pointing directions or extra bandwidth to be obtained.

KAIRA mode-357, 4-bit observation of Cas A from 22 to 249 MHz.
In the plot, you can see that the frequency range (left axis) is from 22 to 249 MHz. The dark blue horizontal bands are regions that we did not observer (due to radio-frequency interference, RFI). The coloured vertical strips are (mostly), ionospheric scintillation. However, you may also notice a pale blue band that runs from 50 to 70 MHz. This is where the signal is being clipped due to a limited number of sampling bits. In other words, there is not enough dynamic range.

If you look at the spectra of the three different RCU modes side-by-side, you see that the peak response of the LBA amplifiers is actually quite high.


The radio spectrum as measured at KAIRA.

When you observing in LOFAR 4-bit mode, the data is effectively clipped. But there is a way around this. What you need to do is attenuate the signal. The system has the ability to apply up to 31-levels of attenuation in 0.26 dB steps.

Yesterday, we carried out an experiment where we set the attenuation from 31 down to 0 at approximately 60 second intervals. The level-31 attenuation was applied at about second 350.

Attenuation being applied to the signal from KAIRA's LBA aerial L08.

If normalised and plotted as a cross section, you can see how the dynamic range is lost in the next figure.

Normalised cross-sections through the data. Red is 0 dB attenuation, blue is 7.75 dB.

In the same way that KAIRA selectively configures the receiver units (RCUs) to use different modes, and hence antennas, it is possible to do the same thing with the attenuation settings. This means that the attenuation can be selectively increased for only those RCUs with LBA antennas. Although it doesn't completely fix the dynamic range issue, it does result in a huge improvement.
A small sample of a KAIRA Mode-357, 4-bit mode observation.

Although not perfect, it does make this mode usable for certain experiments. While loss of some dynamic range is a problem in some cases, the availability of 190.6 MHz total bandwidth is a very attractive prospect indeed!