Showing posts with label Tromsø. Show all posts
Showing posts with label Tromsø. Show all posts

Thursday, 8 May 2014

Day 2: Quadriphase-coded expms continue

Today we will run nearly the same experiment as yesterday. We have slightly modified the quadriphase codes and this naturally affects analysis. We will report the results in Twitter and hopefully also in the blog in the afternoon! Operations commence at 11:00 UT !!!

In addition to the EISCAT UHF and VHF radars, there is a significant number of other instruments at the EISCAT site. From the KAIRA point of view, one of the most interesting instruments is the MORRO 56 MHz MST radar. The MORRO signals can be received with the KAIRA LBA field! Hence, below is a photo of the MORRO antenna field! ... and yes it is again a very beautiful day in Tromsø!!


Friday, 14 February 2014

Sunlit Hamperokken

It is Friday again, and we have a nice photograph to share with you today, submitted by one of our colleagues from the EISCAT facility, just up the road at Romfjordmoen, near Tromsø.

Hamperokken behind the wires of the ionospheric heating facility. (Photo: M. Rietveld)


The image shows the striking peak of 'Hamperokken' lit by the waning sun at 3.00 pm, Thursday 13 February, with some of the HF antennas of the ionospheric heating facility at Ramfjordmoen in the foreground. Taken while Mike Rietveld was digging about 1.5m into the crusty snow to fix some faulty coaxial cable feed lines in preparation for some Heating campaigns in the coming weeks. The unusually large snowfall and subsequent weather in November has caused considerable damage to the coaxial lines.

Thanks Mike for sharing this with us!

Have a good weekend, everyone.

Monday, 25 November 2013

Finnish EISCAT campaign week

This week, we will run a number of Finnish EISCAT experiments both in mainland and Svalbard. KAIRA will support most of the experiments. Monday-Tuesday Antti Kero will run ionospheric heating campaign titled heatncool. Wednesday-Thursday Lassi Roininen et al. have the TomoScand verification campaign. Alexander Kozlovsky will do measurements up in the islands in Longyearbyen. Anita Aikio et al. will make remote runs from Oulu.

Just to give you a clue of some experiments:

Heatncool - 25 and 26 Nov

To measure the D-region heating and cooling rates in a sub-millisecond resolution by superposing a sufficient number of short heater on/off modulations together. Raw data sampling makes the superposition possible.

TomoScand - 27 and 28 Nov

The objective is to verify the TomoScand ionospheric tomography reconstructions against the EISCAT measurements. 27 Nov mourning, we will point EISCAT mainland VHF to zenith with simultaneous KAIRA measurements allowing bistatic incoherent scatter radar measurements. With UHF we follow the trajectories of flybys of a COSMOS satellite. In order to guarantee transmitter stability, we will use regular EISCAT experiments (beata, bella etc).

28 Nov the measurement setup is similar to 27 Nov, except that we will do a daytime experiment. In addition, ESR Svalbard incoherent scatter radar will point at Az 180 El 78 (nearly field-aligned). This pointing direction is towards the Pan-Nordic TomoScand chains, thus allows good additional information for verification studies!

In addition to EISCAT and KAIRA, we will use Tromsø and Sodankylä ionosondes and GPS measurements (gps data handled by our visiting scientist Melessew Nigussie from Bahir Dar University, Ethiopia).

EISCAT heating control!

Thursday, 7 November 2013

EISCAT VHF

Yesterday we showed some photographs of the EISCAT 32m UHF system. Today, we are featuring the 120x40m VHF system. This antenna is actually split into four "panels", which are 30x40m each and can be controlled in elevation independently.

The EISCAT VHF system with the nearest panel tipped
forward. Note the person on the access-way
for scale. (Photo: D. McKay-Bukowski)

The EISCAT VHF system with all panels aligned.
The feed is off-axis, so in this configuration the radar
beam is actually straight up. (Photo: D. McKay-Bukowski)

Looking along the feeder-bridge. The crossed-
dipoles are used for both transmission and
reception. (Photo: D. McKay-Bukowski)

The observing project was being run by the University of Southampton, UK, which has time on both the EISCAT UHF and VHF systems as well as KAIRA.

Wednesday, 6 November 2013

EISCAT UHF

A couple of weeks ago, the KAIRA team was at the EISCAT radar site at Ramfjordmoen, near Tromsø, to carry out some observations. We planned to control KAIRA remotely and do the observations with EISCAT locally. It didn't quite work out that way, as an unexpected power failure required a "quick" return to the site for a reset, but otherwise all went okay.

The weather we had in Tromsø was lovely and we took some photographs to share. Today we are featuring the 32m UHF radar.

EISCAT transmitter hall, control building and UHF 32m dish. (Photo: D. McKay-Bukowski)

The 32m UHF dish, seen from the feeder-bridge of the VHF antenna. (Photo: D. McKay-Bukowski)

Saturday, 26 October 2013

Visit to EISCAT

This week the KAIRA observers have been at the EISCAT facility near Tromsø, Norway. This was to carry out observations of the ionosphere using both the UHF and VHF radars while KAIRA was also observing the same region. During the visit, we had an opportunity to tour some of the facilities, along with other visiting scientists who were there for their own experiments.

Visiting scientists touring the EISCAT facility. (Photo: M. Rietveld)

Saturday, 16 February 2013

DA14 Measurements Running Smoothly

EISCAT Tromsø tracking of asteroid 2012 DA14 is running smoothly.

Haystack joined tracking at 22:00 UT and Goldstone joined at 00:10 UT. All three radar facilities are now tracking DA14. EISCAT will continue until 08:00 UT.

We got a confirmation that Haystack has observed DA14!

Update: Goldstone confirms observation of DA14!

Friday, 15 February 2013

Radar is Running - Testing and Calibration

EISCAT Tromsø switched on 18:00 UT. At the moment, final testing and calibration before the asteroid DA14 flyby.

Tracking asteroid 2012 DA14 starts 20:00 UT!

Transmission test is ok (see photo)!


DA14 European and US Radar Schedules

Three large-scale research facilities will track asteroid 2012 DA14 with radars. The asteroid will be first observable in the European sector and later in the American sector. Tentative schedules are:

EISCAT (Tromsø, Norway) will track Feb 15 20:00-08:00 UT.

Haystack (Massachusetts, USA) will track Feb 15 22:00-08:35 UT.

Goldstone (California, USA) will track Feb 16 00:10-08:35 UT. Goldstone will continue Feb 18, 19 and 20.

Asteroid will not be observable at Arecibo radar in Puerto Rico.

Asteroid diameter is estimated within a factor of two of about 50 meters! Radar observations will give refined estimates on the size and shape!

Thursday, 14 February 2013

Tracking Starts Friday 20:00 UT

24 hours till the first ping of asteroid 2012 DA14! EISCAT Tromsø is now calibrated and secured to track the flyby of DA14.

We will post updates both in the Kaira blog as well as in Twitter during the DA14 flyby from the EISCAT control room (see photo).




Latest photo from the radar prior to DA14 flyby

With a glimmer of sunshine against the mountain tops, and an impressive view, 2012 DA14 observer Lassi Roininen took a moment to take this fantastic photograph of the UHF radar dish at the EISCAT facility at Tromsø, Norway.

EISCAT UHF radar dish and transmitter and control buildings. (Photo: Lassi Roininen)

The event is getting closer, and it's getting exciting. The team are ready and the system is calibrated and set to go.

Wednesday, 13 February 2013

Radar system used for 2012 DA14 observations

The EISCAT facilities near Tromsø (Norway) include a radar there which operates at 931 MHz. This is what the team will be using for their observations of 2012 DA14.

The dish is 32m in diameter and is fully steerable. The radar power is provided by klystron technology and coded radar pulses are transmitted towards the asteroid 2012 DA14.

Using timing, pulse-decoding and all the other required calibration techniques, the faint echoes that are received from the asteroid can be interpreted to discern critical parameters about the fly-by.

Events of this kind are not common and there is a lot of work to be done to prepare the system for the observations. The team is working flat-out to ensure that everything is in order, calibrated, tested and ready for the pass.

Photo: D. McKay-Bukowski

Friday, 6 May 2011

Construction plans — Part 5

With the cabling run out, the next stage is to install the internal electronics within the RF-container. Within it there are four, full-height 482.6mm (19") rack frames. The sub-rack assemblies go into the first three of these and the fourth is for the control computers, clocks and networking. Once the sub-rack assemblies are in place, they can be cabled up with the white signal cables that come from the back of the patch panels.

In addition to this, site clean-up and storage will be done. This means 'dressing' the site, securing all items, packing up equipment and recycling waste. The site is then cleared and we are ready for winter.

Over winter 2011-2012, the first tests between KAIRA and the VHF transmitter at Tromsø will be carried out. And then, in the following year, the LBA will be deployed and the data connection made back to the supercomputer in Groningen.

But that's another story.

So ends our mini-series on what is planned for the summer installation... and the action starts NEXT WEEK!

Thursday, 14 April 2011

High-power large aperture radars

High-power large aperture radars were first envisioned by Bill Gordon (1958) as instruments that can measure the incoherent scatter from free electrons in the Earth's ionosphere. He also proposed that such a radar could be used to observe the Sun and various planetary targets. The first experimental measurements of ionospheric incoherent scatter was soon thereafter reported by Bowles (1958), and many of the other goals were also soon realized when the Jicamarca Radio Observatory and the Arecibo Ionospheric Observatory were built. Both of these radars are still the largest in the world, and have contributed much to our knowledge of Earth's atmosphere and space. The Jicamarca radar located in Peru has a square shaped phased array antenna field with dimensions of 300*300 m. The Arecibo Ionospheric Observatory in Puerto Rico has a spherical dish with a diameter of 305 meters.


Since the early days, many more high-power large aperture radars have been built in various places around the world: These include the Millstone Hill, Svalbard, Tromsø UHF, Tromsø VHF, Kharkiv, Irkutsk, MU, Sondrestrom, PROUST, Poker Flat, and Resolute Bay radars. There are also various large radars of comparable size around the world used for space surveillance purposes. The most recently built Poker Flat and Resolute Bay radars are digital phased array radars, which allow fast beam steering and allow 3D imaging of the ionosphere. The KAIRA receiver array will also be a phased array system, which will function as a bistatic receiver for the Tromsø VHF radar. Some of these radars are shown in the following figure


High-power large aperture radar systems of the world. Photograph credits: Arecibo (NAIC), Jicamarca (JRO), Tromsø (EISCAT Scientific Association), Svalbard (Tony van Eyken), Millstone Hill (MIT Haystack), Kharkiv (Institute of Ionosphere, Kharkiv), Poker Flat and Resolute Bay (Craig Heinsleman).


As the name already suggests, high-power large aperture radars are radars with large antenna aperture and transmission power. As the beam width of an antenna is typically inversely related with the collecting area, these radars also have fairly narrow beams (typically 1 degree). They also typically transmit fairly long coded pulses in order to increase the average transmitted power. In some bi-static planetary radar applications the transmission can be continuous.

While the primary purpose of most high-power large aperture radars is the study of ionospheric plasma, they can also be used for a large variety of other uses, including meteor, space debris, planetary , and lower atmospheric studies.

Monday, 4 April 2011

How do KAIRA and LOFAR work? — Part 8 : Steering a phased array

Last time, we saw that a couple of detectors can be used to collect signals and that because they will add in phase from some directions and not others, there is a certain directionality to the system.

In principle, you can ‘steer’ this system to look in different directions by tipping it, but that’s not particularly efficient. The real advantage is that without moving the antennas you can change the directionality of the overall system by changing the lengths of the cables.

Let’s consider the off-zenith case from the last part.

If we now add a bit of extra cable, these off-zenith signals now add in-phase again.

In fact, the zenith signals are the ones now out of phase when they are combined electrically. So, by adding some cable length, you can control the direction in which the array is sensitive. That is, you can steer its ‘looking direction’ around the sky without actually moving the antennas themselves.

Some phased arrays indeed use cables to adjust their pointing direction. The VHF radar in Tromsø is one such system. It is mechanically steered in the vertical direction and horizontally pointed with a phased array. By manually changing the cables, the horizontal pointing direction of the array can be altered by 15 degrees.

A view inside the feeder bridge of the VHF system
at Tromsø. (Photo courtesy Mike Rietveld)


Because this needs to be done by hand, it is not patch the cables that quickly, so these sorts of directional changes are not done too often.

Although still useful (rotating a 120×40m antenna in azimuth is tricky!) there is another technique which has recently become affordable and which makes arrays like KAIRA, LOFAR and the SKA practical.

Thursday, 10 March 2011

The EISCAT UHF transmitter

If you read the previous web log post about the EISCAT site at Sodankylä, you may be wondering how a dish fitted with a UHF receiver can receive signals from a VHF transmitter at Tromsø. Well, that's because there is actually a second transmitter at the Tromsø site.

As we mentioned in the first post about the EISCAT facilities near Tromsø (Norway), there is a radar there which operates at 931 MHz. Like the receiver dishes in Kiruna and Sodankylä, the UHF transmitter system in Tromsø is also a 32-metre diameter dish, although of a slightly modified design. This is because of the additional waveguides required by the transmitter, which take the high-power signals from the klystrons in the so-called transmitter hall, out to the dish and then through a couple of rotating wave-guide joints to get it to the focal position for beaming into the upper-atmosphere.

Together with the passive receivers at Kiruna in Sweden and Sodankylä in Finland, EISCAT’s Tromsø UHF radar transmitter forms this tri-static system. The UHF system has been operating since 1981, with several major upgrades in the intervening period.

Friday, 25 February 2011

The EISCAT VHF transmitter

As we have seen, the site at Tromsø run by the EISCAT Scientific Association has several instruments. The most significant of these to KAIRA is the VHF transmitter, because its frequency (224 MHz) is within the high-band of the KAIRA system. This frequency is also very close to the proposed frequency of the EISCAT_3D project.

The Tromsø VHF system is a scientific radar. Using the incoherent scatter principle, it transmits radio power into the upper atmosphere and detects the faint radio echoes. From these, it can readily determine the electron density, ratio of the electron temperature to ion temperature, ratio of the ion temperature to ion mass, and the line-of-sight ion velocity.

The Tromsø VHF antenna is huge: 120×40 metres in size. It comprises 4 panels, each 30×40 metres, which can be steered in elevation independently of each other. The system cannot turn in azimuth, but it is possible to reconfigure the phase of the transmitter array to provide a small amount of horizontal directional control.

The transmission power is provided by a klystron. The transmission frequency is 224 MHz (well inside the range of a LOFAR HBA antenna) and the peak transmission power is 1.6 MW. The feed system is a line of 128 crossed dipoles at the focal line of the parabolic-cylindrical antenna panels. This line can be seen to the right of the panels in the first photograph. To get an idea of the scale, that line is actually a corridor and engineers can walk along the inside of it. The second photograph shows a close-up of one of the individual crossed dipoles.

Thursday, 24 February 2011

EISACT Tromsø

Two of the EISCAT radar transmitters are located in Ramfjordmoen, close to the city of Tromsø in Norway. The people working here are employed by The University of Tromsø.

The EISCAT UHF (Ultra High Frequency) radar operates at 931 MHz and is driven by two klystrons with a peak transmission power of 2 MW. The antenna is a 32-metre diameter dish, which weighs about 100 tonnes. It is fully steerable, and can scan at speeds of 80 degrees per minute in both the azimuth and elevation axes. It can accelerate to full speed within 2 seconds.

The other radar is the VHF system, shown in the second photograph. This is a 120×40 metre antenna with a 224 MHz transmitter. This radar is of particular significance to the KAIRA project, so we'll write about it in full tomorrow.

In addition to the radars, there is a Heating Facility, which is used for modification experiments. It applies high-power transmissions of high-frequency electro-magnetic waves to the ionosphere to study its plasma parameters. The name Heating stems from the fact that these high power electromagnetic waves, which are transmitted into the ionosphere with high-gain antennas, heat the electrons and thus modify the plasma state. To create plasma turbulence, the transmitted frequencies have to be close to the plasma resonances, which are 4 to 8 MHz.

There is also a Dynasonde (a digital HF sounder) covering a frequency range of approximately 1-20 MHz. Six dipoles are used as spaced receiving antennas. Each half of each dipole is made from an aluminium tube, 11 metres long and 15 centimetres in diameter. These tubes are suspended about 2 metres above the ground. Even so, they do break sometimes through weight of snow and metal fatigue as they vibrate in the wind.

More information about these systems can be found at the EISCAT website: http://www.eiscat.se/about

But there will be more about the VHF system tomorrow!

Thursday, 10 February 2011

EISCAT

EISCAT can sometimes be a confusing term. Sometimes it refers to the organisation, sometimes the instruments that it operates and at other times to an upcoming project, which is closely connected with our KAIRA work.

The EISCAT Scientific Association is an international research organisation operating three powerful scientific radars in Northern Scandinavia. It is funded and operated by research councils in various member countries. EISCAT itself, stands for European Incoherent SCATter, which is a reference to the radar technique that is used (more on this later!). These radars, along with an Ionospheric Heater and Dynasonde facility are used to study the ionosphere and the interaction between the Sun and the Earth (a field broadly referred to as Solar-Terrestrial Physics).

EISCAT operate several sites. The transmitters are located near Longyearbyen (Svalbard) and Tromsø (Norway). In addition, there are receiver stations located near Kiruna (Sweden) and Sodankylä (Finland) at the SGO site. The headquarters for the EISCAT Scientific Association is located in Kiruna and there are support groups in various of the institutes and universities of the member countries. The transmitter and receiver sites are all marked on the map that was recently posted.

In addition to the existing facilities, EISCAT is now undertaking a new ambitious project - EISCAT_3D. This is a new-generation radar that will provide a huge increase in capabilities of any existing scientific radars. KAIRA, in addition to its own scientific goals and close ties to the LOFAR project, is intricately connected with this EISCAT_3D development work, and there will be a lot more posted about this during the coming months.