Showing posts with label layout. Show all posts
Showing posts with label layout. Show all posts

Thursday, 23 August 2012

An odd numbering scheme

We've had a lot of feedback on our recent successes — thanks to everyone who commented or sent e-mails! However, there was one particular question which came up which probably wants some explanation. Paraphrased, it was:

How did you come up with your antenna numbering scheme?

Yes, I agree that it certainly looks a bit odd, so here's a recap of the reasons and a bit more explanation.

For the High-Band Antenna array, the logic is as follows:

  • The project has 48 'tiles' and we devised the 24+12+12 layout to suit our primary science objectives and environmental concerns.
  • However, we wanted to still keep the option of converting to a full-size LOFAR station one day. That has 96 tiles in a circular pattern, numbered by row, but with a "hole" in the centre (Tile ID = "HCC"). Sets of LOFAR layouts are shown here: http://kaira.sgo.fi/2011/02/hba-layout-part-1-lofar.html
  • So, we superimposed our layout on the standard full-size layout and used the numbering system that resulted. The one tile that would not be in the full size layout was originally referred to by Tile ID = "HXX", which later became "H96".
  • There is a diagram (which should help) here: http://kaira.sgo.fi/2011/06/hba-configuration.html

For the Low-Band Array, the layout (LINK) works like this:

  • A standard LOFAR remote station has 48 aerials in a scatter pattern.
  • We started with this layout for antennas "L00" to "L45".
  • These start "L00" in the centre, then increment anti-clockwise in rings.
  • However, there are two "out-rigger" antennas ("L46" and "L47") in the LOFAR setup which are 80-90 metres away. These could not be used at KAIRA owing to terrain issues.
  • So we made them "fit" somewhere in our array circle, but ran a massive simulation to find the spots where they would give the best beam performance. That's why these last two seem a bit oddly placed.

I hope that clears things up!

Sunday, 12 August 2012

Complete antenna layout

It has been pointed out there has not been a complete antenna layout posted up anywhere. So, we'll fix that today! Here is an overview of both the HBA array and LBA array for KAIRA. This diagram is to scale, including the spacing between the two arrays. The directions to north and the EISCAT VHF transmitter near Tromsø. Also shown are the antenna ID numbers.

Click to enlarge

Sunday, 10 June 2012

LBA location

There have been a number of factors which have influenced the design of the KAIRA array. As a result, it is definitely not a standard layout, as far as regular LOFAR stations are concerned. The primary aim of the station is to satisfy the VHF reception from the EISCAT radar system. This has determined the layout and position of the HBA. The LBA, on the other hand, needs to remain secondary to this and we have tried to work out a suitable configuration that will still allow us to accomplish our complicated scientific requirements.

However, there has been an additional complication: the original LBA field site is simply not stable enough to take the LBA array as originally planned. This has forced a rethink but, in turn, this has actually allowed us to come up with a better solution, that we could not have foreseen before the HBA was built in 2011.

The plan now is to locate the LBA to the south-east of the HBA. This gives a large number of benefits. Firstly, in terms of deployment, this is the easiest area to work with. There are no ground stability issues and there are no problems in terms of vehicle access, which would be the case on the tundra. The new area is also (mostly) in the shadow of the HBA, thus affording additional protection. It is on the raised mound which should also help keep snow levels down.

Proposed area for the KAIRA LBA.


The array area is shown in the following diagram. At this stage the exact placement of individual aerials is not shown, but we will discuss this in another post coming soon.

Saturday, 14 April 2012

Reindeer fence

We continue our series of web log posts about work completed at the end of last year. Although we've been really busy over the winter, we've almost caught up with all the news ready for the next stage of the build this season.

Of course, one of the distinctive features of the KAIRA site is the beautiful wildlife. However, we do need to protect our sensitive experiment from the animals that roams these northern wilds.

As mentioned last year, there was a reindeer fence that was installed around the full site perimeter. The following photograph (by Arttu Jutila) shows the site layout, with a faint yellow line marking the proposed route of the so-called reindeer fence.

As we mentioned the posts for this were installed last summer and the wire spooled out from post to post to secure the area. Here is the wire deployment rig.


Finally, some gate lines were added along the route to permit access. Here is the main entrance during construction last autumn.



As you can see, the snow had started to set in back then. Of course throughout the winter it has been totally covered in snow. Note also the reflective markers. The fence itself is also marked to make it distinct in critical areas. As we also mentioned in a previous post, there are also snow poles around the area to mark difficult or dangerous terrain that may be hidden under the snow and ice.

Wednesday, 29 June 2011

HBA configuration

KAIRA is made up of two arrays... the Low-Band Array (LBA) covers the frequency ranges 30-80 MHz and the High-Band Array (HBA) spans from 120-240 MHz. Firstly, I should start off by pointing out that only the HBA is being built this year. Because the summer is so short in the Arctic, we simply do not have time to get the LBA constructed as well... especially with the added complication of difficult terrain! Instead, we're concentrating on getting the HBA done.

You may recall a long time back, we ran a couple articles (Part-1, Part-2) on the configuration of the High-Band Array. That was before the details calculation of beam patterns, site area planning and the destructive testing after the winter trial period. As we said, the array layout might get revised to adapt to our improved understanding of the array geometry options.

Well, here is the final decided layout.



The actual KAIRA deployment is shown in the darker grey. The faint grey outlines show the location of a LOFAR international station. As we mentioned, we would like to expand the array in the future to have a 'full' international HBA, in addition to the LBA which is already scheduled. This means that our HBA deployment must be made to the same 'grid' as the international layout.

Also shown on the diagram are the tile antenna identifiers (H22, H23, etc.). Again, the scheme used is consistent with the 'international upgrade' idea.

The layout is split into three 'blocks' of 6×4, 6×2, 6×2. By splitting the array into a semi-sparse configuration, it will allow us to try different sub-array combinations for EISCAT_3D. The 'corridors' between them will also be used for snow clearing.

Although winter tests have been carried out, we are still being conservative with our snow strategy and wish to ensure that we have a way of clearing the snow for winter observations.

Tuesday, 15 February 2011

HBA layout — Part 2 (KAIRA)

As we described in yesterday's article, there are three standard configurations for High-Band Arrays (HBAs) in conventional LOFAR stations. KAIRA will also use LOFAR hardware for its antennas, thus making use of the proven design and also retaining compatibility with the LOFAR system. In total, there will be 48 HBA tiles in KAIRA. But although you might first think that the KAIRA layout might look similar to a 'remote station' or perhaps even a two-part 'core station', this is not the case.

There are some constraints on the KAIRA layout. These are:

  • It has to maintain a elongation in the direction of the Tromsø VHF transmitter. This is to maintain the optimal beam pattern when looking at target regions of the ionosphere.
  • There needs to be good access to the site, in order to deploy the tiles, maintain them, and protect them from the Arctic conditions.
  • The volume of levelling of the ground needs to be minimised. This is to save costs, but it also saves valuable time during the extremely short summer when the array will be installed.
  • There needs to be the option to upgrade KAIRA from 48 tiles to a full 96 tiles, thus converting it into a full-size international station.
  • And, that upgrade needs to be done in a way to achieve the standard international layout, with minimum disruption to the existing array.

This means that the most optimal layout is a 4×12 grid. From there, only one row of tiles needs to be removed, and then additional tiles added to the sides, to complete the upgrade to the full international station layout.



The 4×12 layout is then rotated so that it points at an azimuth of 313 degrees with respect to North. This puts it on the alignment axis between Kilpisjärvi and the VHF transmitter in Tromsø (we'll write more on this transmitter soon). Curiously, it is also the same layout as the Kiruna phased array, which is part of the EISCAT_3D prototype work (yes... there be an article on that soon, too!).

Working out how the array (and the possible upgrade) will be placed on the mound, has been a time-consuming process. Because the placement is so critical, a great deal of attention has been paid to the survey and analysis to make sure we get this right

This is what the configuration looks like:



The dark-blue squares are the HBA tiles of KAIRA. The red outlines are the additional tiles that would need to be added to convert KAIRA to a full international LOFAR station configuration. In addition, the four end tiles (in the lower-right) of KAIRA would need to be removed to restore the symmetry. The white dot marks the centre of the international station layout. This would also be the dummy tile in that configuration, although it is a fully active tile in the KAIRA layout.

There will be lots more about the KAIRA configuration and deployment over the coming months.

Monday, 14 February 2011

HBA layout — Part 1 (LOFAR)

As described in our previous article, LOFAR is a pan-European telescope, split into stations and in each station there is typically two arrays of antennas: the High-Band Array (HBA) and the Low-Band Array (LBA). KAIRA, which is based on LOFAR antenna hardware, will also have an HBA and LBA. But the question is what sort of LOFAR station will it be?

You see, even though LOFAR is split into many stations, not all LOFAR stations are the same. In the Netherlands — the centre of the LOFAR network — where the stations are close together, there are more of them, but they are smaller.

One of the LOFAR stations near the core of the network. Note that
there are two small patches of HBA tiles. The 'shotgun pattern' of
antennas in between them is the LBA. (Photo: LOFAR Gallery)

As you move out from the centre of the network, the stations get bigger and their configurations change. This is for a number of reasons to do with performance, cost and ease of deployment. In this article, we'll only consider the HBA in the station, as this is where the changes are the most striking and where the most pronounced difference between LOFAR and KAIRA will be realised.

Essentially, there are three types of standard LOFAR station:

  • Core stations = 2 × 24 HBA tiles
  • Remote stations = 48 HBA tiles
  • International stations = 96 HBA tiles

This is what these configurations look like (note you can click on any of the weblog images to see larger versions):

As you can see, in reality there is one additional tile right in the centre of the international station layout. This is not an active antenna... just an empty tile. This keeps the RF-load balanced across the array and prevents wind-turbulence cells being generated at the 'hole in the middle'. There is a more detailed explanation of this on the LOFAR-UK weblog article 'Going the extra tile'.


The completed HBA at the Chilbolton LOFAR
station in Hampshire, UK. (Photo: STFC Images)

So that's the description of the LOFAR station HBA layouts. But what of KAIRA?

Despite having the same hardware, KAIRA is quite different and with some distinctive features, dictated by its multi-purpose applications, challenging build site and some interesting future plans.

But we'll discuss that in tomorrow's web log post!

Wednesday, 2 February 2011

LOFAR

LOFAR (LOw Frequency ARray) is a pan-European radio telescope designed to observe the radio universe at VHF frequencies. It is designed, built and operated by ASTRON, the Netherlands Foundation for Radio Astronomy. The LOFAR system is split across multiple sites — known as stations — each of which typically has two arrays of antennas.

The antennas in each of these two arrays are different in design. One design is a vertical 'aerial' which stands about 1.8 m tall, optimised for radio frequencies in the range 30 to 80 MHz. The other design is a large 'tile', with a square area of 5 × 5 m. It is for the higher frequency range of 120 to 240 MHz.

Did you note the gap from 80 to 120 MHz? LOFAR deliberately avoids these frequencies, as this is where commercial and public FM-radio stations broadcast. There is no point trying to listen for faint cosmic radio signals at the same frequency as a high-powered neighbouring radio station.

In addition to a large cluster of LOFAR stations in the Netherlands, there are additional participants in the main LOFAR project: Germany, France, Sweden and the United Kingdom. This map is a closer view than the one posted earlier, and shows the locations of the LOFAR stations (green = complete, yellow = under construction).


KAIRA makes use of the same antenna technology that is used in LOFAR, making it compatible with the LOFAR system. This opens up some exciting prospects of linking the two projects. We'll be looking at these antenna systems soon.

In addition, there have just been some important achievements by the LOFAR project. More on that in the next post!

Tuesday, 1 February 2011

Putting LOFAR, EISCAT and KAIRA on the map

As one might guess from the name, the Kilpisjärvi Atmospheric Imaging Receiver Array is located in Kilpisjärvi. For those of you who didn't already know, Kilpisjärvi is a small border town located in the top-left-hand corner of Finland. It is usually very easy to find on a map, as it is quite close to the corner of the three countries: Norway, Sweden and Finland.

But possibly less familiar are the related LOFAR and EISCAT projects associated with KAIRA.

This map marks the sites of these project with EISCAT in pale blue and LOFAR in magenta. KAIRA itself is marked in red. At a latitude of +69 degrees north, KAIRA is located well above the Arctic Circle (marked in white), making its association with LOFAR a most northerly one indeed.

There'll be more about LOFAR and EISCAT over the coming weeks, so be sure to visit this weblog again soon.