Recently we showed a photograph of the re-surveying of the heights of the Low-Band Antenna (LBA) array at KAIRA. Today, we have the results from that survey.
The plot shows the heights of each antenna in the array with respect to the average height. For the purposes of a phased array, the relative positions are important. Our concern had been that freezing/thawing of the ground would result in shifts in the surface. Additionally, there might be some subsidence on the side where the mound had been built up to match the main field height. In these cases, it is possible that the soil is not sufficiently well packed and that it sinks slightly as it settles further.
As can be seen from the data, the heights are all within the +/- 3 cm specification.
Showing posts with label survey. Show all posts
Showing posts with label survey. Show all posts
Tuesday, 8 July 2014
Friday, 4 July 2014
Re-surveying the LBA
As part of the summer maintenance, we surveyed the LBA heights. One of the concerns was that the freeze/thaw cycle in the soil and gravel that supports the LBA would cause subsidence or a minor 'palsen' effect which in turn would distort the array field.
To carry out this test, we used a laser level and investigated the relative heights of the different aerials. This task was carried out by some of our summer workers.
To carry out this test, we used a laser level and investigated the relative heights of the different aerials. This task was carried out by some of our summer workers.
![]() |
| Conducting the LBA survey with the laser level is in the foreground. (Photo: D. McKay-Bukowski) |
Sunday, 8 July 2012
LBA field levelled and surveyed
The Low-Band Antenna array field has now been levelled. The next stage is then to mark out the location of the aerials. The aerials are scattered about in a 40-metre diameter circle. The scatter pattern is not random, even though it looks like it. The reason for this pattern is to improve the beam-shape of the sparse array. By spreading out the aerials, you can increase the resolution, but you need to do so carefully to avoid aliasing effects (called side- or grating-lobes) from becoming problematic.
The layout that we are using is modelled closely on that of the inner configuration of a Dutch Remote Station ("RS"). The two outlier antennas are brought into the array and two additional calibration aerials will be installed later. Although it looks like some of the aerials overlap, it is actually on the ground planes that intersect. The aerials themselves at the array centre are close-packed but do not physically interfere with each other.
Each position has two survey pegs. The first at the northern edge of the aerial ground plane defines the position. The second constrains the rotation. We'll discuss this in a later web log post.
These survey positions were provided to a survey company who completed the layout of the pegs.
The next stage on the LBA construction is the installation of the cable trenching and ducts. However, there is also a lot of HBA work about to start up. Keeping up with the web log is always a major challenge over the busy Arctic summer build season. But there's lots to follow so do make sure you visit regularly and keep up to date with the progress.
The layout that we are using is modelled closely on that of the inner configuration of a Dutch Remote Station ("RS"). The two outlier antennas are brought into the array and two additional calibration aerials will be installed later. Although it looks like some of the aerials overlap, it is actually on the ground planes that intersect. The aerials themselves at the array centre are close-packed but do not physically interfere with each other.
![]() |
| Design of the KAIRA LBA layout. (D. McKay-Bukowski & J. Vierinen). |
Each position has two survey pegs. The first at the northern edge of the aerial ground plane defines the position. The second constrains the rotation. We'll discuss this in a later web log post.
| One of the survey pegs on the LBA field. Photograph by Arttu Jutila. |
These survey positions were provided to a survey company who completed the layout of the pegs.
| Marking the GPS points was finished rather quickly thanks to the GPS specialist. This is a view of the LBA field taken on top of a HBA tile. Photograph by Arttu Jutila. |
The next stage on the LBA construction is the installation of the cable trenching and ducts. However, there is also a lot of HBA work about to start up. Keeping up with the web log is always a major challenge over the busy Arctic summer build season. But there's lots to follow so do make sure you visit regularly and keep up to date with the progress.
Sunday, 10 June 2012
LBA location
There have been a number of factors which have influenced the design of the KAIRA array. As a result, it is definitely not a standard layout, as far as regular LOFAR stations are concerned. The primary aim of the station is to satisfy the VHF reception from the EISCAT radar system. This has determined the layout and position of the HBA. The LBA, on the other hand, needs to remain secondary to this and we have tried to work out a suitable configuration that will still allow us to accomplish our complicated scientific requirements.
However, there has been an additional complication: the original LBA field site is simply not stable enough to take the LBA array as originally planned. This has forced a rethink but, in turn, this has actually allowed us to come up with a better solution, that we could not have foreseen before the HBA was built in 2011.
The plan now is to locate the LBA to the south-east of the HBA. This gives a large number of benefits. Firstly, in terms of deployment, this is the easiest area to work with. There are no ground stability issues and there are no problems in terms of vehicle access, which would be the case on the tundra. The new area is also (mostly) in the shadow of the HBA, thus affording additional protection. It is on the raised mound which should also help keep snow levels down.
The array area is shown in the following diagram. At this stage the exact placement of individual aerials is not shown, but we will discuss this in another post coming soon.
However, there has been an additional complication: the original LBA field site is simply not stable enough to take the LBA array as originally planned. This has forced a rethink but, in turn, this has actually allowed us to come up with a better solution, that we could not have foreseen before the HBA was built in 2011.
The plan now is to locate the LBA to the south-east of the HBA. This gives a large number of benefits. Firstly, in terms of deployment, this is the easiest area to work with. There are no ground stability issues and there are no problems in terms of vehicle access, which would be the case on the tundra. The new area is also (mostly) in the shadow of the HBA, thus affording additional protection. It is on the raised mound which should also help keep snow levels down.
![]() |
| Proposed area for the KAIRA LBA. |
The array area is shown in the following diagram. At this stage the exact placement of individual aerials is not shown, but we will discuss this in another post coming soon.
Saturday, 9 June 2012
LBA survey work
Here are some photographs taken from the LBA survey. We used a combination of metal survey tapes, laser levels, laser ranger finders and direct and trilateration measurements.
![]() |
| Measuring and recording another field height. |
![]() |
| A path of snow cleared for the laser level. |
Wednesday, 17 August 2011
LBA centre
At the conclusion of the LBA survey work (carried out by Mikko Orispää and Juha Vierinen), a centre mark was driven deep into the ground. This is the centre point of the entire LBA array and the mark on the top has been measured accurately to be sent to ASTRON for them to calculate the coordinate locations for the individual antenna elements.

The taller, thinner post to the side of the centre mark is just a snow pole. It should (just) be visible over the snow allowing us to find the mark in winter if required.
Photo: D. McKay-Bukowski

The taller, thinner post to the side of the centre mark is just a snow pole. It should (just) be visible over the snow allowing us to find the mark in winter if required.
Photo: D. McKay-Bukowski
Monday, 15 August 2011
LBA survey work
Although not due until next year, the survey for the LBA (Low-Band Array) was carried out at the beginning of the month.
It's amazing to think that it is less than a year since Markku Postila and I did the same work for the HBA. That seems like an eternity ago!
It's amazing to think that it is less than a year since Markku Postila and I did the same work for the HBA. That seems like an eternity ago!
Thursday, 14 July 2011
Checking alignment
The observing frequency for the High-Band Array is 120 to 240 MHz. That's a wavelength of 2.50 to 1.25 metres. In order to achieve good beamforming and interferometric performance, the positional tolerance of the receiver elements still needs to be a small fraction of a wavelength. That means that KAIRA still has a tight error budget. And, given that the positional accuracy is only one factor, and that other aspects of the design such as cable delay errors and timing can also affect the performance, additional accuracy is required. Thus, the KAIRA antenna tiles need to be positioned to ±3cm.Over long distances, this requires a fair amount of surveying work, not just for the initial marling out of the locations, but also in checking the work that has been done. In the photograph to the left, Mikko Tilja and Tero Raita check the alignment of a sighting laser. This is used to ensure a straight edge along the centre block of antenna tiles. Despite a good local accuracy, we discovered a small rotational error which, if left uncorrected, would result in a large error at the far end of the field.
The amount of corrective work required has been minimal, but it is still useful to cross check all the work done so far to ensure the best possible performance from the array.

Additional work is planned for the vertical position of the antennas. Again, although the field looks flat, we need it to be good to a centimetre across the field, which is a pretty tight tolerance to be required.
Photos: D. McKay-Bukowski
Sunday, 26 June 2011
HBA survey
With the High-Band Array (HBA) field finally level, it is time to start work on the survey for the antennas themselves.The HBA tiles are actually 5×5 metre squares, which are spaced in a regular grid comprising a few sections (6×4, 6×2 and 6×2). Overall, however, the tile grid is regular, and the gaps are also 'tile sized'.
Because there needs to be a small gap between tiles for water run-off, fittings, anchors and so on, the actual 'grid increment' is 5.148 metres exactly. So the field is then marked out according to this.
A number of reference marks were taken first. From these the precise direction to the EISCAT VHF transmitter in Tromsø was calculated (azimuth = 314.1762 degrees).
The original corner reference mark was then checked with a multi-satellite receiver system (top left photograph) and the field corners were measured. At this point a slight correction was applied to optimally centre the array on the field (which helps with issues such as possible erosion and access).
With the new reference mark, the corners were re-calculated with the correct azimuth. Then all the intervening grid points were calculated.In addition to this, four triangulation points were measured. These then served as the calibration points for the surveyors total station, which was used to do the final mark out.
Once the corners have been measured, small metal pegs are driven into the ground to mark their locations. These are quite fine!
Additionally, checks are made to ensure that the spacing is correct and that the grid is properly set out.
It is certainly interesting to see all the pegs in place. It happened very quickly (the work was completed in about 24 hours).
With the pegs in place, additional layout work can now start. This is for marking the location of the cable-tunnels and the position of the cable mausoleum. More on that later.

Photos: D. McKay-Bukowski
Friday, 4 February 2011
Mound Mesh Model
As reported in our piece on the site survey, we need to accurately model the region where we intend to put the KAIRA antennas. Unlike most LOFAR stations, KAIRA is located in pretty rugged terrain. This means that finding a suitable space is not as easy as it first appears. Especially when we are trying to avoid cutting down trees and keeping our impact on the Arctic wilderness to the barest minimum.
The site we have selected fits these requirements pretty well. The ground is mostly material from civil works, allowing us to re-use an existing development. However, the space is not easy to work in, especially when the main antenna array has an area of over 1200 m2., which needs to be levelled to an accuracy of ±3 cm. As a result, we need to consider well the exact location of the array and the amount of levelling required.
The plot shown here is from part of that analysis work. From the survey results, a topographic mesh is fitted to the data. That is then interpolated to derive a working model of the surface. From this, the detailed planning and layout can be completed.

The map is oriented with North at the top and the direction to the EISCAT VHF transmitter marked.
The site we have selected fits these requirements pretty well. The ground is mostly material from civil works, allowing us to re-use an existing development. However, the space is not easy to work in, especially when the main antenna array has an area of over 1200 m2., which needs to be levelled to an accuracy of ±3 cm. As a result, we need to consider well the exact location of the array and the amount of levelling required.
The plot shown here is from part of that analysis work. From the survey results, a topographic mesh is fitted to the data. That is then interpolated to derive a working model of the surface. From this, the detailed planning and layout can be completed.

The map is oriented with North at the top and the direction to the EISCAT VHF transmitter marked.
Wednesday, 8 September 2010
Surveying the field
The top priority task is to conduct an initial survey of the proposed deployment area. This was carried out today at the site using a simple theodolite, tape and survey stick... backed up with a GPS receiver! During the survey, a number of set positions were used. This photograph shows the theodolite set up at the primary position.
During the surveying work a number of reindeer passed by to see what we were doing!
Looking across the theodolite, there is a nice view of the area where the low-frequency array could possibly be deployed. One of the survey team can be seen holding the 5-metre survey stick.
During the surveying work a number of reindeer passed by to see what we were doing!
Looking across the theodolite, there is a nice view of the area where the low-frequency array could possibly be deployed. One of the survey team can be seen holding the 5-metre survey stick.
Subscribe to:
Posts (Atom)







