I'm happy to announce that our proof-of-concept study on the electron
density profile estimation based on the KAIRA spectral riometry
measurement has been finally published in the Geophysical Research
Letters, please have a look:
Kero, A., J. Vierinen, D.
McKay-Bukowski, C.-F. Enell, M. Sinor, L. Roininen, and Y. Ogawa (2014),
Ionospheric electron density profiles inverted from a spectral riometer
measurement, Geophys. Res. Lett., 41, doi:10.1002/2014GL060986
By
comparing our spectral riometry results to a simultaneous EISCAT VHF
measurement, we were able to show that the methodology works, at least
under conditions of relatively strong ionisation. This builds confidence
towards continuous monitoring of height-dependent D-region ionisation
by spectral riometry.
Showing posts with label riometer. Show all posts
Showing posts with label riometer. Show all posts
Monday, 1 September 2014
Wednesday, 9 April 2014
KAIRA film
At the LOFAR Science Workshop 2014 in Amsterdam, we premièred the KAIRA film. This was produced by SiteEye in conjunction with Sodankylä Geophysical Observatory, U. Oulu, ASTRON, EISCAT, and many others. (Versions with subtitles in many languages will be posted later.)
Enjoy!
UPDATE!
The film is also available with Finnish subtitles (LINK).
Labels:
ASTRON,
EISCAT,
EISCAT_3D,
Film,
KAIRA,
LOFAR,
radio astronomy,
radio telescope,
riometer,
site-eye
Sunday, 2 March 2014
Software defined radio wide band wide beam riometer
During my visit to Finland a few weeks ago, I setup two computers with two different prototype radio frontends to test my idea of using a USRP N200 and a single LOFAR LBA antenna as a low cost riometer with next generation capabilities.
First of all, a riometer (Relative Ionospheric Opacity METER) is an instrument that measures the absorption of cosmic radio noise in the D-region of the Earth's ionosphere. We assume that the cosmic radio noise statistics are unchanged. Thus, we assume that at a certain time of celestial day, we should pick up the same cosmic radio noise power with our antenna beam, as it sees the same swath of sky. The only variations to this power is attributed to changes in ionospheric absorption, which is significant below 50-100 MHz.
In reality the radio sky isn't a completely stationary noise source. Occasionally there are radio emissions from the Sun, which are sporadically seen as spikes in power during the daytime in riometer data. Jupiter is also a strong and variable radio source, and its emissions might cause confusion when interpreting riometer measurements. These type of sporadic emissions need to be excluded from any ionospheric data products derived from riometer measurements.
The advantage of using a wide band for riometry is at least four fold:
First of all, a riometer (Relative Ionospheric Opacity METER) is an instrument that measures the absorption of cosmic radio noise in the D-region of the Earth's ionosphere. We assume that the cosmic radio noise statistics are unchanged. Thus, we assume that at a certain time of celestial day, we should pick up the same cosmic radio noise power with our antenna beam, as it sees the same swath of sky. The only variations to this power is attributed to changes in ionospheric absorption, which is significant below 50-100 MHz.
In reality the radio sky isn't a completely stationary noise source. Occasionally there are radio emissions from the Sun, which are sporadically seen as spikes in power during the daytime in riometer data. Jupiter is also a strong and variable radio source, and its emissions might cause confusion when interpreting riometer measurements. These type of sporadic emissions need to be excluded from any ionospheric data products derived from riometer measurements.
The advantage of using a wide band for riometry is at least four fold:
- More bandwidth = more statistics
- We get a measure of the frequency dependent absorption, which contains information about the electron density height profile
- More tolerance to interference, as we can find the noise floor around the interference, as long as it doesn't completely saturate the amplifiers.
- The wide band nature of the instrument allows us to more easily identify transient radio emission events, such as Solar or Jovian radio emissions.
Anyway, here are some of the initial results. This is simply a dynamic spectrum and a raw power plot derived from the dynamic spectrum. I have not attempted to yet fit a quiet day surface to extract the frequency dependent absorption, although there is no reason why this wouldn't be possible as we have already done it successfully with the LOFAR digital backend.
I'd like to acknowledge Tomi Teppo and Toivo Iinatti for their assistance in setting up these wide band wide beam riometers.
Saturday, 5 October 2013
Targeted riometry campaign
In October/November, there will be a major KAIRA campaign involving SGO, University of Southampton (Soton), Rutherford Appleton Laboratory (RAL) and the Netherlands Foundation for Radio Astronomy (ASTRON). The objective is to carry out a main riometry measurement campaign, execute a pulsar-polarisation experiment and support some EISCAT VHF time. During this time we also aim to carry out some outstanding calibration measurements that hitherto remain undone and complete remaining installation work.
Yesterday, KAIRA observer-in-charge Derek McKay-Bukowski drove up to KAIRA a few days ahead of time, as he needs to carry out the Rb-clock distributor board upgrade prior to the campaign.
![]() |
| KAIRA observer-in-charge ready to depart to KAIRA. |
Wednesday, 2 October 2013
Riometric beams
When we talk about riometry, there are several different varieties. Obviously, there is single-beam, integrated all-sky riometry ("old school"), but the modern variety makes positionally resolved measurements by putting multiple "beams" on the sky.
KAIRA has been doing this now for quite a while, in addition to some single-beam work and new advanced techniques that are now being developed. However, to get an idea "where" on the sky these beams are, today we are featuring an all-sky image from earlier this year, with the beam centres superimposed over it.
Note that the beam "circles" are not to any scale. Also, the large loop is not a single beam, but rather the path that the "Cas A beam" follows as Cas A tracks across the sky. The slight discrepancy in the Cas A source and beam position is due to the fact that the displayed data is not calibrated.
KAIRA has been doing this now for quite a while, in addition to some single-beam work and new advanced techniques that are now being developed. However, to get an idea "where" on the sky these beams are, today we are featuring an all-sky image from earlier this year, with the beam centres superimposed over it.
Note that the beam "circles" are not to any scale. Also, the large loop is not a single beam, but rather the path that the "Cas A beam" follows as Cas A tracks across the sky. The slight discrepancy in the Cas A source and beam position is due to the fact that the displayed data is not calibrated.
Thursday, 18 July 2013
The challenge of calibrating
Calibration can be tricky business. Especially when you get interesting scientific events occurring during the calibration process. Recently, we were attempting to measure the on/off source fluxes to estimate KAIRA's sensitivity. Two problems crept in: ionospheric scintillation and ionospheric opacity.
In the plot, the vertical axis is labelled "beamlet number", but it is linearly-proportional to frequency. The horizontal axis is time. Red is strong radio emission and blue is very weak. The two main blocks in the middle of the plot are Cygnus A and Cassiopeia A.
If you look at the top of them (around beamlets 320-400), you can see a "colourful fringe". This is ionospheric scintillation. We know about this and the solution is to time-average to smear it out.
However at the lower frequencies (roughly beamlets 50-130) there are also some odd effects. In particular, around samples 7000-8000 there is a large drop in radio strength from Cygnus A. This is caused by increasing electron density in the ionosphere (around 80km up).
In this plot it is pretty obvious, but it certainly caused us to puzzle over the rather odd results when we were trying to figure out why the Cygnus A measurements gave such completely different ones to the Cassiopeia A equivalent.
In the plot, the vertical axis is labelled "beamlet number", but it is linearly-proportional to frequency. The horizontal axis is time. Red is strong radio emission and blue is very weak. The two main blocks in the middle of the plot are Cygnus A and Cassiopeia A.
If you look at the top of them (around beamlets 320-400), you can see a "colourful fringe". This is ionospheric scintillation. We know about this and the solution is to time-average to smear it out.
However at the lower frequencies (roughly beamlets 50-130) there are also some odd effects. In particular, around samples 7000-8000 there is a large drop in radio strength from Cygnus A. This is caused by increasing electron density in the ionosphere (around 80km up).
In this plot it is pretty obvious, but it certainly caused us to puzzle over the rather odd results when we were trying to figure out why the Cygnus A measurements gave such completely different ones to the Cassiopeia A equivalent.
Tuesday, 29 January 2013
Seminar on the riometer application
On behalf of our reseach team*, I'd like to show a few slides on the recent development of KAIRA as a multi-frequency riometer with a title
"Electron density height profiles derived from a broad-band riometer"
![]() |
| Photo by Sami Kero |
2 pm (Finnish local time) at SGO. That is 12 UTC for all our friends abroad.
The plan is to stream the presentation here for anyone to follow. Just login as "guest" and type your name in it.
See also earlier posts related to the topic here and here.
Welcome, physically or virtually,
*Antti Kero, Juha Vierinen, Derek McKay-Bukowski, Carl-Fredrik Enell, Malefia Sinor, Lassi Roininen, Yasunobu Ogawa
Wednesday, 9 January 2013
Inversion of electron density from multi-frequency absorption measurements
Riometers were discussed a while ago on this blog. In essence, these are instruments that measure how much radio waves are absorbed in the D-region of the ionosphere (50-100 km). The more electron density in this region, the more absorption is observed. The absorption is also dependent on frequency of the radio wave. The higher the frequency, the lower the absorption. The amount of absorption is determined by comparing cosmic radio noise power to typical values for "normal" quiet day, where we would expect to know the amount of absorption based on ionospheric models.
A few months ago we managed to capture an auroral precipitation event that caused clear absorption. This aurora was also captured at the Sodankylä Geophysical Observatory by the all-sky camera.
KAIRA was running in wide band riometer mode during this time with 244 subbands observing the vertical direction. You can see the measured values of absorption in the following figure.
![]() |
| Measured absorption on the vertical beam of the LBA, starting from 12 UT on 13.11.2012. Notice that while there is some man-made radio interference, most of the LBA band is pretty clean. |
![]() |
| The best model fit the the measurements. |
![]() |
| The resulting electron density (N_e/cm^3) profile that was fitted. |
Tuesday, 11 December 2012
KAIRA as a multi-frequency riometer
![]() |
| Photo: Carl-Fredrik Enell |
"My name is Malefia Sinor, I’m a student in Lappeenranta University of Technology, in where I am doing a masters thesis in collaboration with Sodankylä Geophysical Observatory. My topic is to search for a parameterized model for the D-region electron density to be used in a multi-frequency riometer data analysis.
"Riometer (relative ionospheric opacity meter) is an instrument used to measure the cosmic HF radio noise absorption that is taking place in the D-region ionosphere (50-90 km). Traditionally, riometers measure the cosmic radio noise only at one or two single frequencies, typically around 40 MHz. Depending on the amount of ionization, the radio signal is absorbed when it passes through the ionosphere. The ionosphere is the partially ionized region of the Earth’s upper atmosphere. It extends from about 60 km to 1000 km. The absorption takes place mainly in the lowest part of the ionosphere, due to collisions between the free electrons and neutral particles.
"KAIRA instrument turns out to be a unique riometer, because of its capability to measure a wide range of different HF frequencies in multiple narrow beams. The multi-frequency capability is the one which makes it possible to invert the electron density since the height profile of the refractive index of the plasma depends on the radio wave frequency for a given electron density profile.
"To share experience and to get an idea about my work, I traveled to Sodankylä. When I arrived, the weather was -20oC (or more), which is for me very cold, I never imagined this kind of weather and I almost couldn’t survive from it for the first time, but peoples at SGO were very helpful. For the last week, I have had an opportunity to attend to the Finnish EISCAT campaign in Tromsø, Norway. After we drove for several hours from Sodankylä to Tromsø, we finally arrived to the EISCAT site. It was ecstatic to see the control room and the receiver when the radar equipments were introduced to us. I’m enjoying my stay on the site, seeing the magical white mountains and the sparkle of the northern lights, and gaining experience of the space physics research in practise."
Tuesday, 19 April 2011
Atmospheric research at Kilpisjärvi — Part 2
Today we continue our guest article series by Tero Raita.
Monitoring of cosmic radio noise absorption in the D-region ionosphere (50-90km) by riometers (relative ionospheric opacity meter) started in 1980. Since 1997 SGO has operated Imaging Riometer for Ionospheric Studies (IRIS) together with University of Lancaster (for more details see: http://spears.lancs.ac.uk/iris/ ). 64 antenna elements forms 49 beams, which are sampled once per second. Beams of IRIS Kilpisjärvi overlap with present EISCAT radar range and EISCAT heater beam. And, of course, they will also overlap with the KAIRA project.
Geomagnetic field variations in Kilpisjärvi have been measured with variometer and three component search coil magnetometer. In 1983 Kilpisjärvi received an EISCAT cross magnetometer station. Today the variometer is part of the wider IMAGE magnetometer network. Search coil magnetometer, which are able to see higher frequencies of the field variations like Pc1 magnetic pulsations, was deployed for the support of Swedish satellite projects (FREJA and POLAR) and the instrument was operated by Department of Physics (University of Oulu). Today the whole Finnish pulsation network is operated by SGO.
Monitoring of cosmic radio noise absorption in the D-region ionosphere (50-90km) by riometers (relative ionospheric opacity meter) started in 1980. Since 1997 SGO has operated Imaging Riometer for Ionospheric Studies (IRIS) together with University of Lancaster (for more details see: http://spears.lancs.ac.uk/iris/ ). 64 antenna elements forms 49 beams, which are sampled once per second. Beams of IRIS Kilpisjärvi overlap with present EISCAT radar range and EISCAT heater beam. And, of course, they will also overlap with the KAIRA project.
Geomagnetic field variations in Kilpisjärvi have been measured with variometer and three component search coil magnetometer. In 1983 Kilpisjärvi received an EISCAT cross magnetometer station. Today the variometer is part of the wider IMAGE magnetometer network. Search coil magnetometer, which are able to see higher frequencies of the field variations like Pc1 magnetic pulsations, was deployed for the support of Swedish satellite projects (FREJA and POLAR) and the instrument was operated by Department of Physics (University of Oulu). Today the whole Finnish pulsation network is operated by SGO.
Subscribe to:
Posts (Atom)












